Setting up my G35 on KW V3 coilovers didn’t just make it look better, it also reduced lap times by over 2-seconds once we got the alignment dialled in using Stillen adjustable camber arms and the DIY alignment tools you’re about to read about.
One of the mods we do first to our project cars is a coilover suspension conversion, because nothing — exceptwheels and tires — transforms a car’s performance and attitude more than this relatively simple upgrade. We pretty much always start with wheels, tires and coilovers, because these really do work together as an overall package and, when done right, give your car a ton more grip and style. We certainly understand when the wallet turbo can’t handle all these mods in one big step, though, so no judgement here if you’re still chipping away at this all-important set of mods on your own project. It’s far more important to buy quality parts than it is to build your car quickly.
As for the specific advantages of a high quality coilover setup, we’ve covered that in a number of our FR-S stories and in our first stage of ASS2000 upgrades, but to summarize here, you get dampers (preferably with adjustable compression and rebound) capable of controlling higher spring rates, which in turn reduce body motion and thus improve roll control, which lets those stickier and wider tires you’ve invested in work their best. Plus with ride height adjustability you can reducethat heinous wheel well gap while corner balancing for optimum weight distribution. Just don’t go too low or you’ll start to ruin your car’s suspension geometry, a topic we’ll cover in a separate post.
So you’ve bolted up the best coilover shock and spring package you can afford and have set the ride height and hopefully even corner balanced it, but you’re not done yet! You need a proper wheel alignment, since any change to ride height will result in a change in wheel alignment, and what you don’t want to do is start driving around on a messed up alignment and trash those expensive new tires.
There are two ways to come at this, the first being a professional 3D alignment at a performance shop like NV Auto, which is equipped with a top-of-the-lineHunter alignment setup and knows how to dial in a proper high-performance street or race alignment. Whatever you do, avoid those “Quicky Alignment” or generic maintenance shops, because those placeswill just rough it in to OEM specs, and that’s not what you want if generating more grip and cornering speed on the street and at the rack track is what you’re shooting for. You’re going to want negative camber well outside the OEM specs at the very least, along with more front caster (if you can get it) and possibly some toe-in or toe-out depending on the chassis you’re working with and what sort of handing characteristics you’re aiming for.
But if you’re like us and enjoy a DIY approach and want to beable to fine-tune the alignment at the race track so that you can make the alignment adjustments the tire temperature data you’re collectingusing that probe-type tire pyrometer we urged you to buy in our latest Just The Tip video, then you’ll need to invest in a few simple tools including a camber gauge, toe plates, a string box setup and some measuring tapes. Having a ramp setup like GMG does above is, of course, the ballin’est DIY setup since it gives you a platform you can perfectly level for maximum alignment accuracy, but as long as your garage floor or paddock space at the track is reasonably level (and you can shim each wheelof the car a bit with shingles or tiles or whatever you have handy), you’re still going to get very close to where you want to be alignment-wise.
There are a lot different camber gauges on the market, and there are even some decent home-made options for very little money (Google DIY camber gauge and you’llsee what we mean). We prefer a professionally builtdigital camber gauge, though, which cost about $100-200 but makes the job much quicker because the arms at each end that allows you to hold the tool flush against the top and bottom lip of the wheel are adjustable and if used properly won’t scratch the finish on the wheels. The digital inclinometer attached to the straight edge of the level gives you a camber readout in degrees, and in our experience these are quite accurate as long as the car is parked on a level surface. Some higher end camber gauges correct for the angle of the surface via a calibration process or even via GPS, but for best results it is still a good practice to find the flattest and most level surface you can before getting started. And of course make sure you bring the tools needed to physically adjust the camber on your car, which may involved camber plates, camber bolts, eccentric bolts or camber arms, depending on the vehicle and how you’ve modified it.
Keep in mind, camber is best used as a way of maximizing tire grip while under lateral load, meaning cornering, so don’t think of it as a way of adjusting the car’s handling balance (though in extreme cases it can be used to reduce the size of the contact patch and thus adjust the grip level and handling balance). As I described in that Just The Tip video, the best way to figure out optimum camber settingsis by using a probe-type tire pyrometer to measure tire temperatures at the race track. What you want to aim for is tire temps in the optimum operating range for the tire (which for high-performance street tires and race tires is generally in the 160-220F range), but with temps about 10-20F higher on the inside third of the contact patch than on the middle third and outer third. Many professional race teams and tire manufacturers have proven that this type of temperature spread across the contact patch delivers the fastest lap times, and at the end of the day that’s all that really matters.
Which brings me to the importance of keeping notes. I’ve been using Laptimizer, an iPad appthat’s designed to let racers keep accurate setup notes and then download them to Microsoft Excel or text or email them in PDFformat. The reason I bring this up is that having notes on your alignment settings is really useful at the track, since any changes you make that don’t work can easily be set back to where you started.
Plus if you’ve got marked camber plates or adjusters like the KW Clubsport front top plates on our Scion FR-S, you’ve also got excellent reference points for any changes you’ve made, so keep notes on those as well. The more data you collect, the faster you’ll be able to dial your car in for maximum grip the next time you’re at the track.
Ok, now back to the DIY part of aligning your car’s contact patches. Checking and setting camber is really pretty easy, but things get a little more difficult when it comes to toe, or the direction each tire is aimed relative to the front-to-rear centreline of the chassis. You can check toe quite easily with toe plates and a couple of measuring tapes, which can be bought as a kit for about $60-80 from companies like Longacre, but keep in mind this only gives you total toe measured across the front and rear axles. So, for example, if the measurement across the front of the front tires is 1/4” longer than the measurement across the rear of the front tires, then you have a total of 1/4” toe-out across the front axle, but you don’t know if that means all the toe-out is on one wheel or if it’s split 1/8” out on each side.
1 2
